EV CPS2.9 PDF

Designed for the contractor, the CPS MK II feature 2-RU chassis, Phoenix-type connectors for inputs and outputs, pre-programmable power-on delay, easy power-on via remote contact closures, rear panel attenuators, and a switchable 50 Hz high-pass filter. Like the CPS multi. Two-Channel Models CPS, CPS, CPS, and CPS CPS2.x rear view. Remote power-on contact. 1. Programmable power-on timer. 2. Module slot for. Buy Electro-Voice CPS 2-Channel Power Amplifier for RCM IRIS-Net Remote Control Module (W, 4 Ohms) Review Electro-Voice CPS

Author: Turisar Malami
Country: Russian Federation
Language: English (Spanish)
Genre: Photos
Published (Last): 26 July 2015
Pages: 214
PDF File Size: 10.84 Mb
ePub File Size: 17.87 Mb
ISBN: 293-9-76744-211-8
Downloads: 30925
Price: Free* [*Free Regsitration Required]
Uploader: Vulkree

Mains Switch The Mains Switch on the front panel separates the power amp from the mains. Please read and follow the instructions provided in the documentation that you have received together with each extension module. Introduction 1 Introduction 1.

By pressing ‘print’ button you will print only current page. PARALLEL operation is the mode of choice, whenever the same input signal drives multiple power amp channels of a large system installation.

Attach the power amp as shown in the illustration using 4 case nuts and screws. Mounting CPS amplifiers have been designed for installation in a conventional inch rack case.

In this case, bridging the screen shielding and the pin of the inverting input inside of the connector is mandatory. The power drawn from the mains network is converted into output power to feed the connected loudspeaker systems and into heat. To print the manual completely, please, download it.

  LOVCEVI ZAPISI PDF

Failure to do so may result in damage to the power amplifier as well as to the rack case. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintance servicing instructions in the The audio signal has to be applied to the input connectors of channel 1.

CPS 2.9 MK II

Controls, Indicators and Connections Front View 1. Additionally securing the amplifier at the rear becomes necessary, if the rack case in which the power amplifier has been installed will be transported. The difference between power consumption and dispensed power is called power dissipation P d.

Inputs are electronically balanced. For pricing options and packages, contact us at Unbalanced connections should only be used if the cables are very short and no interfering signals are to be expected in the vicinity of the power amplifier. Show all Contractor precision cps2. Only the provided power cord may be used.

The power amplifier remains cooler and dissipating the developing waste heat in a specific direction gets easier. Do not use the power amplifier near heat sources, like heater blowers, cpz2.9 or any other heat radiating devices.

  ABMAXX PRO ANLEITUNG PDF

The audio signal has to be applied to the input connectors of channel 1, amplification is set via input level control of channel 1 only.

CPS MK II Contractor Precision Series Class‑H Power Amplifier by Electro‑Voice

Turning the Mains Switch to ON cps29. booting up the power amp. When installing the power amp in a case or rack system, attention should be paid to these details to provide sufficient ventilation. Brackets for securing the power amplifier are available as accessories. Electrovoice contractor precision cps1: Comments to this Manuals Your Name.

Electro-Voice CPS2.4 Owner’s Manual

Do not modify this unit! Attach the power amp with its frontal rack mount ears using 4 screws and washers as shown in following illustration. Make sure to completely read and fully observe power rating specifications of the speaker systems to be used and to check them against the output power capacity of the power amp. Page of 24 Go.

This mode of operation is being used for all 2-channel applications, like stereo operation. Electrovoice contractor precision cps2t: Extremely high voltages can be present at the output.