HT12D DECODER DATASHEET PDF

HT12D 2 12 Series of Decoders Features. Operating voltage: V~12V Low power and high noise immunity CMOS Built-in oscillator needs only 5% resistor. For proper operation, a pair of encoder/decoder with the same number of Of this series, the HT12D is arranged to provide 8 address bits and 4 data bits, and. IC HT12D can be used only with its pair HT12E. These two ICs together form an Encoder and Decoder pair. They are bit.

Author: Kazizil Kegor
Country: Ukraine
Language: English (Spanish)
Genre: Education
Published (Last): 24 September 2012
Pages: 423
PDF File Size: 2.93 Mb
ePub File Size: 6.42 Mb
ISBN: 225-7-52304-136-7
Downloads: 60458
Price: Free* [*Free Regsitration Required]
Uploader: Zolomuro

The IC is has a wide range of operating voltage from 2. Valid transmission; active high. So if you are working on a project which has to transmit a 4-bit data from one end to other either by wire or wireless then this IC pair will be best suited for you. The IC is should be powered by 5V pin 18 and the ground pin pin 9 is grounded. For decoding a data the IC will requires an oscillator, luckily this IC has one in-built.

HT12D/HT12F – Product Details – Holtek

This oscillator can be used by connecting these two pins through a 1M Resistor. Can range from 2.

These two ICs together form an Encoder and Decoder pair. This data should be sent to the HT12D for decoding, it can either be sent directly through a wire or by using a wireless medium like RF or IR.

HT12D Decoder IC

They are paired with 2 12 series of encoders. Photograph just for reference. Connected to the Ground of circuit. The data on 4 bit latch type output pins remain unchanged until new is received.

In this image I have made all four data bits as zero lowwhen this is decoded we will get the same kind of bits on the output side of HT12D, similarly we can make any changes on these 4-bits and they will be reflected on the output side of the HT12D decoder IC. Please submit the url of the better price you saw.

  DURUFLE TOCCATA PDF

The encoded bit can be obtained from the Dout pin pin If any valid data is received they can be obtained from these four pins. In the above circuit I have set the 8-bit address data as 0b, by dtasheet all address pins to ground. A valid transmission in indicated by a high signal at VT pin. The input data code is decoded when no error or unmatched codes datasyeet found. It is not mandatory to use it. SPI Module of Arduino.

HT12E Encoder IC Pin Diagram, Uses, Equivalents & Datasheet

So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. These are the 8-bit address bits, which is used to protect your data. We will notify you the result by email. Skip to main content. This oscillator can be used eecoder connecting these two pins through a 1M Resistor. These two ICs together form an Encoder and Decoder pair. These are the 8-bit address bits, which is used to protect your data.

The serial input data is compared with the eecoder addresses three times continuously.

They can also be connected to switches to manually send and receive data. We will lauch an immediate investigation and try our best to beat the price, if it proves to be the same product. This ICs are paired with each other.

Arduino based GPS receiver. The Decoder receive the serial address and data from its corresponding decoder, transmitted by a carrier using an RF transmission medium and gives output to the output pins after processing the data. It is mainly provided to interface RF and infrared circuits.

  EXPERIMENTAL ORGANIC CHEMISTRY PALLEROS PDF

The Encoded 12 bit output data obtained from HT12E has to be given here. The Encoded 12 bit output data can be obtained from this pin.

This pin powers the IC should use only 5V. The 4-bit data that is received can be obtained on pins AD0 to AD1 and an address of 8-bit has to be set using the pins A0 to A7. Customers who bought this product also purchased TL — Programmable Reference Voltage.

We should set the bits in same pattern on Encoder and Decoder IC to pair them. Found this item with same quality and at a lower price decder prefer to buy from robokits. To know how a 4-bit data can be encoded and then send to the input pin of this IC, we have to understand the working of the HT12E Encoder IC which is given decodef. If you want security you can connect any of the 8 pins to 5V to make it high.

Buy 15 or more pieces to get Free Shipping Option Edcoder So out of the bits 8-bits will be used to set address and the remaining 4-bit will be used to transmit data. We should set the bits in same pattern on Encoder and Decoder IC to pair them. This pin will go high when a data is received. Hh12d simple terms, HT12D converts the serial input into parallel outputs. Can be used in Home automation for short range remote switching Safety systems like Burglar alarm system, Smoke or Fire alarm system etc.